View GW6BGS30ED_6526385.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

these specifications contain 17 pages including the cover and appendix. if you have any objections, please contact us before issuing purchasing order. customers acceptancedate: by: presentedby: dept. general manager reviewed by: prepared by: development department lighting device divisionelectronic components and devices group sharp corporation model no. gw6bgs**hed spec no. issue 23may12 product type zenigata led dg125027 s p e c i f i c a t i o n s s p e c i f i c a t i o n s s p e c i f i c a t i o n s s p e c i f i c a t i o n s ** : 27, 30, 40, 50 reference http://www..net/ datasheet pdf - http://www..net/
handle this document carefully for it contains material protected by international copyright law. any reproduction, full or in part, of this material is prohibited without the express written permission of the company. when using the products covered herein, please observe the conditions written herein and the precautions outlined in the following paragraphs. in no event shall the company be liable for any damages resulting form failure to strictly adhere to these conditions and precautions. (1) please do verify the validity of this part after assembling it in customers products, when customer wants to make catalogue and instruction manual based on the specification sheet of this part. (2) the products covered herein are designed and manufactured for the following application areas. when using the products covered herein for the equipment listed in paragraph (3), even for the following application areas, be sure to observe the precautions given in paragraph (3). never use the products for the equipment listed in paragraph (4). ? office electronics ? instrumentation and measuring equipment ? machine tools ? audiovisual equipment ? home appliances ? communication equipment other than for trunk lines (3) these contemplating using the products covered herein for the following equipment which demands high reliability, should first contact a sales representative of the company and then accept responsibility for incorporating into the design failsafe operation, redundancy, and other appropriate measures for ensuring reliability and safety of the equipment and the overall system. ? control and safety devices for airplanes, trains, automobiles, and other transportation equipment ? mainframe computers ? traffic control systems ? gas leak detectors and automatic cutoff devices ? rescue and security equipment ? other safety devices and safety equipment, etc. (4) do not use the products covered herein for the following equipment which demands extremely high performance in terms of functionality, reliability, or accuracy. ? aerospace equipment ? communications equipment for trunk lines ? control equipment for the nuclear power industry ? medical equipment related to life support, etc. (5) please direct all queries and comments regarding the interpretation of the above four paragraphs to a sales representative of the company. please direct all queries regarding the products covered herein to a sales representative of the company. gw6bgs**hed model no. http://www..net/ datasheet pdf - http://www..net/
dg125027 1. application these specifications apply to the light emitting diode module model no. gw6bgs**hed.[ led module (ingan blue led chip + phosphor) ] main application : lighting 2. external dimensions and equivalent circuit refer to page 2.3. ratings and characteristics refer to page 3 5. 31. absolute maximum ratings32. electrooptical characteristics 33. derating curve 4. reliability refer to page 6. 41. test items and test conditions42. failure criteria 5. quality level refer to page 7. 51. applied standard52. sampling inspection 53. inspection items and defect criteria 6. supplements refer to page 8 12. 61. chromaticity rank table62. packing 63. label 64. indication printed on product 7. precautions refer to page 13 15. gw6bgs**hed 1 of 15 gw6bgs**hed specifications model no. page http://www..net/ datasheet pdf - http://www..net/
dg125027 1. external dimensions and equivalent circuittop view side view (note) values inside parentheses are reference values. external dimension of ceramic substrate is the indication of maximum length at each side. equivalent circuit (note) 12 series 5 parallel = 60 pcs of leds model no. page gw6bgs**hed 2 of 15 mm 52404006 substrate : alumina ceramic unit drawing no. material + connection terminal - connection terminal ( 10.0 ) ( 1.6 ) 15.0 + 0.50 / 0.10 1.0 0.1 12.0 + 0.50 / 0.10 ( 6.5 ) ( 11.6 ) unit = mm r http://www..net/ datasheet pdf - http://www..net/
dg125027 3. ratings and characteristics 31. absolute maximum ratings *1 power dissipation and forward current are the value when the module temperature is set lower than the rating by using an adequate heat sink. *2 voltage resistible at initial connection error (not dealing with the possibility of alwayson reverse voltage.) *3 case temperature tc (refer to measuring point for case temperature in the next page.) refer to "derating curve" in the next page as for operating current. *4 t c = 25 model no. page gw6bgs**hed 3 of 15 item symbol rating unit power dissipation *1,4 p 25.7 w forward current *1,4 i f 650 ma reverse voltage *2,4 v r 15 v operating temperature *3 t opr 30 + 100 storage temperature t stg 40 + 100 http://www..net/ datasheet pdf - http://www..net/
dg125027 32. electrooptical characteristics (t c = 90 ) (note) values inside parentheses are shown for reference purpose only. *5 (after 20 ms drive, measurement tolerance: 3 %) *6 monitored by sharp's 8 inch integrating sphere and otsuka electronics mcpdle3400 (after 20 ms drive, measurement tolerance: 10 %) *7 monitored by sharp's 8 inch integrating sphere and otsuka electronics mcpdle3400 (after 20 ms drive, measurement tolerance: 0.005) *8 monitored by sharp's 8 inch integrating sphere and otsuka electronics mcpdle3400 (after 20 ms drive, measurement tolerance: 2) model no. page gw6bgs**hed 4 of 15 ** min. typ. max. unit common i f = ma 31.6 (36.0) 39.6 v 865 (995) lm (0.460 4) (0.415 0) (2 700) k 90 (93) 915 (1055) lm (0.437 5) (0.410 0) (3 000) k 90 (93) 955 (1100) lm (0.384 6) (0.384 6) (4 000) k 90 (92) 970 (1120) lm (0.347 6) (0.360 6) (5 000) k 87 (90) 40 luminous flux *6 i f = 30 luminous flux *6 i f = 400 ma ra item symbol condition forward voltage *5 v f 400 400 50 luminous flux *6 i f = chromaticity coordinates *7 x y color temperature general color rendering index *8 27 luminous flux *6 i f = ma chromaticity coordinates *7 x y color temperature general color rendering index *8 ra 400 ma chromaticity coordinates *7 x y color temperature general color rendering index *8 ra ma chromaticity coordinates *7 x y color temperature general color rendering index *8 ra 400 http://www..net/ datasheet pdf - http://www..net/
dg125027 33. derating curve (note) to keep the case temperature lower than the rating, enough heatradiation performance needs to be secured by using an adequate heat sink. for soldering connection, please evaluate in your circumstance to make sure soldering reliability. ( above derating curve is specified to led device, not for soldering connection ) and please consider to avoid physical stress between wire and substrate, and some protection like silicon bond on top of soldered wire is recommended. please ensure the maintenance of heat radiation not to exceed case temperature over the rating in operation. measuring point for case temperature model no. page gw6bgs**hed 5 of 15 forward current derating curve 0 100 200 300 400 500 600 700 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 case temperature t c [ ] forward current i f [ma] measuring point http://www..net/ datasheet pdf - http://www..net/
dg125027 4. reliability the reliability of products shall be satisfied with items listed below. 41. test items and test conditions confidence level: 90 % no. test item test conditions samples defective ltpd n c (%) 1 temperature cycle 40 (30 min) + 100 (30 min), 100 cycles 11 0 20 2 temperature humidity t stg = + 60 , rh = 90 %, time = 1000 h storage 11 0 20 3 high temperature t stg = + 100 , time = 1000 h storage 11 0 20 4 low temperature t stg = 40 , time = 1000 h storage 11 0 20 5 steady state operating t c = 60 , i f = 400 ma, time = 1000 h life 11 0 20 6 shock acceleration: 15000 m/s 2 , pulse width: 0.5 ms direction: 3 directions (x, y and z) 3 trials in each direction 5 0 50 7 vibration frequency: 100 to 2000 hz for 4 minutes per trialacceleration: 200 m/s 2 direction: 3 directions (x, y and z) 4 trials in each direction 5 0 50 42. failure criteria no. parameter symbol failure criteria 1 forward voltage v f v f initial value 1.1 2 luminous flux initial value 0.7 model no. page gw6bgs**hed 6 of 15 http://www..net/ datasheet pdf - http://www..net/
dg125027 5. quality level 51. applied standard iso28591 52. sampling inspection a single normal sampling plan, level s4. 53. inspection items and defect criteria no. item defect criteria classification aql 1 no radiation no light emitting major defect 2 electrooptical not conforming to the specification characteristics (forward voltage, luminous flux and chromaticity) 3 external not conforming to the specified dimensions dimensions (external dimensions of and shown in page 2) 4 appearance nonconformity observed in product appearance is determined minor as defective only when electrooptical characteristics is affected by. defect 0.4 foreign material, scratch, or bubble at emitting area: 0.8 mm fiber generation at emitting area: 0.2 mm in width and 2.5 mm in length foreign material at connection terminal: 0.8 mm substrate burr on edge: over dimension tolerance (note) products with removable foreign material attached on is not determined to be defective. 0.1 model no. page gw6bgs**hed 7 of 15 http://www..net/ datasheet pdf - http://www..net/
dg125027 6. supplements 61. chromaticity rank table (tolerance: x,y 0.005 i f = 400 ma, t c = 90 ?? point 1 point 2 point 3 point 4 x 0.4591 0.4527 0.4617 0.4681 y 0.4210 0.4090 0.4090 0.4210 ? ? gw6bgs**hed 8 of 15 ?? ** 27 chromaticity diagram 0.390 0.400 0.410 0.420 0.430 0.440 0.450 0.460 0.470 0.480 x y 1 2700k 2600k 2800k http://www..net/ datasheet pdf - http://www..net/
dg125027 (tolerance: x,y 0.005 i f = 400 ma, t c = 90 ?? point 1 point 2 point 3 point 4 x 0.4362 0.4298 0.4388 0.4452 y 0.4160 0.4040 0.4040 0.4160 ?? ? ? gw6bgs**hed 9 of 15 ** 30 chromaticity diagram 0.385 0.395 0.405 0.415 0.425 0.415 0.425 0.435 0.445 0.455 x y 1 3000k 3100k 2900k http://www..net/ datasheet pdf - http://www..net/
dg125027 (tolerance: x,y 0.005 i f = 400 ma, t c = 90 ?? point 1 point 2 point 3 point 4 x 0.3833 0.3769 0.3859 0.3923 y 0.3906 0.3786 0.3786 0.3906 ?? ? ? gw6bgs**hed 10 of 15 ** 40 chromaticity diagram 0.360 0.370 0.380 0.390 0.400 0.365 0.375 0.385 0.395 0.405 x y 1 4100k 3900k 4000k 3800k http://www..net/ datasheet pdf - http://www..net/
dg125027 (tolerance: x,y 0.005 i f = 400 ma, t c = 90 ?? point 1 point 2 point 3 point 4 x 0.3463 0.3399 0.3489 0.3553 y 0.3666 0.3546 0.3546 0.3666 ? ? gw6bgs**hed 11 of 15 1 ?? ** 50 chromaticity diagram 0.340 0.350 0.360 0.370 0.380 0.325 0.335 0.345 0.355 0.365 x y 5000k 4900k 5100k 1 http://www..net/ datasheet pdf - http://www..net/
dg125027 62. packing one tray composed of 80 pieces 5 trays (400 piecies) and one upper lidtray in one moistureproof bag 2 bags (800 pieces) in one carton dimensions of outer carton: 235 220 90 mm (reference value) (note 1) there are cases of one carton composed of one bag. (400 pieces)(note 2) state of packing is subject to change. outer carton one bag one tray 400 pieces 2 bags = 800 pieces 80 pieces 5 trays = 400 pieces 10 8 80 pieces 63. label following label is attached on moistureproof bags. 1) lot no. indication (note 3) label format is subjected to change. x x 2 2 g 0 1 0 0 1 a production plant code shipping year year last digit shipping month 1 9 or o, n, d fixed code g shipping date 01 31 serial no. backup code a 64. indication printed on product model no. and control no. are indicated on substrate surface. 1) control no. indicated as follows; g s * * d - 1 f 0 1 abbreviated model no. chromaticity rank month of production (to be indicated alphabetically with january corresponding to a) date of production (01 31) page gw6bgs**hed 12 of 15 model no. (225mm) (210mm) (gw6bgs**hedx) quantity. quantity. quantity. quantity. 400 400 400 400 lot no. lot no. lot no. lot no. xx22g01001a xx22g01001a xx22g01001a xx22g01001a part no. part no. part no. part no. gw6bgs**hed gw6bgs**hed gw6bgs**hed gw6bgs**hed corporation made in xxxxxxxxxx r.c r.c r.c r.c sharp sharp sharp sharp sharp label rank 1 rank 1 rank 1 rank 1 shipment table ? made in philippines ? made in indonesia model number (model number + suffix code) quantity and rank lot no. bar code production country control no. http://www..net/ datasheet pdf - http://www..net/
dg125027 7. precautions storage conditions please follow the conditions below. ? before opened: temperature 5 30 , relative humidity less than 60 %. (before opened led should be used within a year) ? after opened: temperature 5 30 , relative humidity less than 60 %. (please apply soldering within 1 week) ? after opened led should be kept in an aluminum moisture proof bag with a moisture absorbent material (silica gel). ? avoid exposing to air with corrosive gas. if exposed, electrode surface would be damaged, which may affect soldering. usage conditions this product is not designed for the use under any of the following conditions. please confirm performance and reliability well enough if you use under any of the following conditions; ? in a place with a lot of moisture, dew condensation, briny air, and corrosive gas. (cl, h 2 s, nh 3 , so 2 , no x, etc.) ? under the direct sunlight, outdoor exposure, and in a dusty place. ? in water, oil, medical fluid, and organic solvent. ? please do not use component parts contain sulfur (gasket packing, adhesive material, etc.). heat radiation if forward current (i f ) is applied to singlestate module at any current, there is a risk of damaging led or emitting smoke. equip with specified heat radiator, and avoid heat stuffed inside the module. installationmaterial of board is alumina ceramic. if installed inappropriately, trouble of no radiation may occur due to board crack or overheat. please take particular notice for installation. refer to the following cautions on installation. ? apply thermolysis adhesive, adhesive sheet or peculiar connector when mounted on heat radiator.in case of applying adhesive or adhesive sheet only, check the effectiveness and reliability before fixing. if led comes off from heat radiator, unusual temperature rise entails hazardous phenomena including device deterioration, coming off of solder at leads, and emitting smoke. ? when led device is mechanically fixed or locked, please take into consideration regarding the method of attachment due to fail from stress. ? avoid convexly uneven boards.convex board is subject to substrate cracking or debasement of heat release. ? it is recommended to apply adhesive or adhesive sheet with high thermal conductivityfor radiation of heat effectively. ? please take care about the influence of color change of adhesive or adhesive sheet in initial and long termperiod, which may affect light output or color due to change of reflectance from backside. model no. page gw6bgs**hed 13 of 15 http://www..net/ datasheet pdf - http://www..net/
dg125027 ? do not touch resin part including white resin part on the surface of led.no light emission may occur due to damage of resin or cutting wire of leds by outer force. when using tweezers, please handle by ceramic substrate part and avoid touching resin part. for mounting, please handle by side part of ceramic or the specified area shown below. connecting method in case of solder connecting method, follow the conditions mentioned below. ? use soldering iron with thermo controller (tip temperature 380 ), within 5 seconds per one place. ? secure the solderwettability on whole solder pad and leads. ? during the soldering process, put the ceramic board on materials whose conductivity is poor enough not to radiate heat of soldering. ? warm up (with using a heated plate) the substrate is recommended before soldering. ( preheat condition: 100 150 , within 60 sec ) ? avoid touching a part of resin with soldering iron. ? this product is not designed for reflow and flow soldering. ? avoid such lead arrangement as applying stress to solderapplied area. ? please do not detach solder and make resolder. ? please solder evenly on each electrodes. ? please prevent flux from touching to resin. static electricity this product is subject to static electricity, so take measures to cope with it. install circuit protection device to drive circuit, if necessary. drive method ? any reverse voltage cannot be applied to leds when they are in operation or not. design a circuit so that any flow of reverse or forward voltage can not be applied to leds when they are out of operation. ? module is composed of leds connected in both series and parallel. constant voltage power supply runs off more than specified current amount due to lowered v f caused by temperature rise. constant current power supply is recommended to drive. cleaning avoid cleaning, since silicone resin is eroded by cleaning. colortone variation chromaticity of this product is monitored by integrating sphere right after the operation. chromaticity varies depending on measuring method, light spread condition, or ambient temperature. please verify your actual conditions before use. model no. page gw6bgs**hed 14 of 15 handling area http://www..net/ datasheet pdf - http://www..net/
dg125027 safety ? looking directly at leds for a long time may result in hurt your eyes. ? in case that excess current (over ratings) are supplied to the device, hazardous phenomena including abnormal heat generation, emitting smoke, or catching fire can be caused. take appropriate measures to excess current and voltage. ? in case of solder connecting method, there is a possibility of fatigue failure by heat. please fix the leads in such case to protect from short circuit or leakage of electricity caused by contact. ? please confirm the safety standards or regulations of application devices. ? please careful not to injure your hand by edge of ceramic substrate. ? other cautions guarantee covers the compliance to the quality standards mentioned in the specifications, however it does not cover the compatibility with application of the enduse, including assembly and usage environment. in case any quality problems occurred in the application of enduse, details will be separately discussed and determined between the parties hereto. model no. page gw6bgs**hed 15 of 15 http://www..net/ datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of GW6BGS30ED

	To Download GW6BGS30ED Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .